Anti-Fog Coated PET Film
- Material:PET / APET polyester substrate
- Coating:One-side or two-side hydrophilic anti-fog coating
- Color:Clear transparent
- Common thickness:50-250um, custom range available
- Format:Roll, sheet, slit roll, die-cut blank
- Use:Chilled food lids, display covers, and face-shield window trials when required compliance documents are available
Heat Protect Film Company manufactures Anti-Fog Coated PET Film for refrigerated displays, food lids, clear packaging windows, and medical face shield materials where moisture reduces visibility. This hydrophilic anti-fog coated PET film, part of the Functional PET Films range, helps condensed water spread into a thin clear layer instead of forming fog droplets. In controlled condensation, breath fog, and 10-20 cycle wet-cloth wipe observations, sample film kept stable clarity, low haze, and a clean coated surface for chilled packaging, die cutting, and lamination trials. Food-contact or medical uses require the corresponding compliance documents; the anti-fog coating alone does not create that compliance.
Product Overview
Anti-Fog Coated PET Film is made for transparent PET parts that need to stay clear after temperature change, high humidity, or breath exposure. Standard PET may look clean before use, but condensation can form tiny droplets that scatter light and create a cloudy view. The coated surface changes how moisture behaves, helping water spread more evenly so the film remains clearer in refrigerated display lids, chilled tray covers, and transparent window parts.
Heat Protect Film Company controls substrate selection, coating direction, coating uniformity, roll winding, and sample inspection before shipment. For food lids and packaging windows, the anti-fog side normally faces the humid product side. For visor windows or protective panels, two-side coating can be selected when moisture may touch both surfaces. From our sample checks, oily gloves, dust, solvent vapor, pressure marks, or rough wiping can affect anti-fog consistency more than PET thickness itself. Anti-fog durability should be confirmed under the temperature and humidity conditions of the real application, not only after a short condensation or breath-fog check. Coating wear and wipe resistance should also be reviewed if the surface will be cleaned in use. Choose one-side anti-fog coating when moisture comes from one side, such as a food lid or packaging window; choose two-side coating when both surfaces may see condensation, such as an inspection window or visor.

Benefits
- Helps condensed moisture spread into a thin water layer instead of visible fog droplets.
- Keeps refrigerated display lids, salad tray covers, fresh packaging, and viewing windows easier to inspect.
- Typical light transmission: 88-90%, depending on substrate thickness and coating grade. Typical haze is <=3% as an already published in-house typial, not as an unconditional guarantee.
- One-side coating works for packaging lids, while two-side coating suits visors and inspection windows.
- Roll or sheet formats can be tested before printing, die cutting, lamination, or sealing trials.
- Wet-cloth wipe observation, usually 10-20 light cycles, helps check coated-side stability after handling.
- Coating streak inspection and die-cut edge checks help reduce visible defects in clear parts.
What should be checked before using Anti-Fog Coated PET Film in packaging or window materials?
Before bulk converting, the coated PET material should be tested under real temperature and humidity conditions. For chilled food packaging, the coated side should face the humid product side, and samples should be observed after moving from room temperature to a 5 C refrigerated condition. Humidity and duration should follow the agreed cold-fog method and report when they are not separately published. Engineers should check whether moisture gathers into fog droplets or spreads into a clearer layer, and should also review warm-fog performance and condensation recovery time by the agreed method. Those unpublished temperatures or recovery times are not stated as fixed values here. For medical face shield windows or transparent panels, clarity after breath exposure, haze change, coated-side cleanliness, and wipe resistance after soft cloth cleaning are often more important than thickness alone, and any food-contact or medical use still requires the corresponding compliance documents.
TDS
Item | Typical Value |
Product type | Hydrophilic anti-fog coated PET film |
Base material | PET / APET polyester film |
One-Side / Two-Side Coating | One side or both sides, as already published |
Coated-Side Identification | Confirm on the roll, label, or approved sample so the anti-fog side faces the moisture source |
Hydrophilic Coating Uniformity | Confirm by inspection and approved sample |
Appearance | Clear, transparent, no obvious coating streaks |
Common thickness | 50-250 um |
Width range | 300-1250 mm, slit roll available |
Light transmission | Typical light transmission: 88-90%, depending on substrate thickness and coating grade |
Haze | Typical <=3% as an already published in-house typial, not as an unconditional guarantee |
Anti-fog mechanism | Water droplet spreading into a thin clear layer |
Cold-Fog Test | In-house sample test at 5 C refrigerated condition; humidity and duration are confirmed by the test method and report when they are not separately published |
Warm-Fog Test | Confirm by the agreed method and test report; no unpublished temperature is stated here |
Condensation Recovery Time | Confirm by the agreed method and test report; no unpublished recovery time is stated here |
Wet-Cloth Wipe Cycles | Wet-cloth wipe observation, 10-20 light cycles, as already published |
Coating Adhesion | Confirm by the agreed method and test report |
Haze Change After Wiping | Confirm after the agreed wipe method and sample state |
Storage condition | 15-30 C, 40-60% RH, clean and dry warehouse |
Handling note | Avoid oil, dust, solvent vapor, pressure marks, and abrasive contact on the coated side |
Food-contact / medical compliance | Food-contact or medical uses require the corresponding compliance documents. An anti-fog coating alone does not create that compliance. |
Applications
- Refrigerated food display lids for salad, fruit, deli food, and fresh packaging, when the required food-contact documents are available.
- Chilled tray covers where inner condensation may reduce shelf visibility.
- Clear packaging windows for fresh food, prepared meals, and cold-chain display packs.
- Medical face shield window material requiring low haze and breath fog control, only where the corresponding medical or device compliance documents are available.
- Die-cut PET anti-fog functional film parts for covers, visors, and inspection windows.
- Laminated structures where the anti-fog side must face the moisture source.

How does a hydrophilic anti-fog coating keep PET film clear during condensation?
A hydrophilic anti-fog coating changes how moisture sits on the PET surface. On untreated PET film, condensed vapor can collect as many fine droplets. These droplets scatter light, so the surface looks cloudy even when the base film is transparent. On a properly coated PET substrate, water spreads into a thinner and more uniform layer, helping the surface stay clearer during refrigeration, humid packaging, or breath exposure. Anti-fog performance should be checked together with light transmission, haze, coating uniformity, coated-side identification, wipe resistance, cold-fog testing, and, where required, warm-fog testing and condensation recovery time, not only by appearance before use.
Coating and batch confirmation
Before volume coating, approve the substrate, one-side or two-side coating arrangement, coated-side identification, and the agreed anti-fog checks. Keep a retained sample as the comparison standard for later lots. Record substrate lots, coating lots, and finished-goods lots. Inspect rolls for thickness, coated-side cleanliness, coating uniformity, roll face, edges, and winding. Confirm thickness tolerance by grade and method, winding direction by the coated-side and line requirement, and slitting tolerance by the final part size. Repeat orders should be checked against the approved sample and those batch records.
Loading Details

FAQ
Which side should face the moisture source?
The anti-fog coated side normally faces the humid side, such as the food side in chilled packaging or the breathing side in visor use. Coated-side identification should be confirmed on the roll or approved sample.
Can this PET anti-fog functional film be printed?
Printing is usually tested on the non-coated side. Ink type, drying temperature, and adhesion should be confirmed before bulk production.
Does wiping affect the anti-fog coating?
Soft wet-cloth wiping can be tested, but abrasive cleaning, solvent contact, or oily gloves may reduce coated-side performance. Haze change after wiping should be reviewed by the agreed method.
What should be tested before bulk production?
Check condensation spreading after refrigerated storage, haze, coated-side direction, and whether die cutting or wiping affects surface clarity. Food-contact or medical uses also need the corresponding compliance documents, not only an anti-fog result.












